42 1957 chevy truck wiring diagram
Does anybody happen to have the wiring diagram for the 14/16 connector? I am fixing a Chevy Silverado 2009, with a cut factory harness. So far I have only been able to find the standard wires. I need the full diagram to retain onstar, chimes and steering wheel controls. Example: Like a diagram or something but simple enough where I can click “Audio” and under audio I can select say “speakers” and it shows the locations on the picture/model of selected vehicle. I wanna put work into my chevy, not sure how you guys just find where things are so easily lol.
In the last week or so, random problems that I believe to be electrical have popped up, including the failing of the Odometer and Speedometer. Yesterday, After driving around 30 miles or so, I parked for an hour and a half and it would not start again, instead I could hear what I believe is the flywheel clicking, but the engine would not crank. I tested the battery voltage last week and it seemed fine, and ran my OBD battery test which said the battery is good today. The only codes coming back ...

1957 chevy truck wiring diagram
Update as of September 04 2020. SOLVED! After digging around the wiring system looking for issues I finally found it... there is a ground on the spare tire bracket under the bed. This ground has a ground wire from the trailer accessories harness and the ground for the rear tail light harnesss. So a total of two ground wires attached. The trailer harness was grounded well but the tail light ground wire was corroded internally. It looked ok but after checking for continuity it read “open”. I repl... Because when I got my system installed I brought the wires needed and told them. But when I got my car back the wires were still in my seat. And the guy on the phone before hand asked me what a big 3 upgrade was and I had to tell him🤦 I recently got my truck running but the ignition switch doesn't work anymore, and theres some messed up wiring for oil pressure, turn signals and I'm assuming other stuff. Somehow it's isolated to the gauges and ignition system, fan and other lights work as normal.
1957 chevy truck wiring diagram. Truck I'm working with is legally a 1980 chevy k20, however it has bits and pieces from all over the time spectrum. The current electrical system mostly follows the original schematics. Regardless of the make, old vehicles use mechanical contact style switches for everything. I'd like to rewire the truck to make use of a modern style fuse and relay block. Im willing to start almost entirely from scratch to clean this up. What I'm looking for specifically is references. Most of what I have ... Hello everybody. I am looking for a wiring diagram for the battery cables. I've recently changed out the battery in my truck going from a top post to side post battery. In the process of doing that I had to change out some wires. After everything was back together the truck still does not have power. Edit: the motor is a 5.7 350. I have checked the battery and it has a charge, and the starter is not the issue. Any help and advice would be greatly appreciated. Thank you all. [http://www.wrxinfo.com/service\_manuals/](http://www.wrxinfo.com/service_manuals/) Been researching some torque specs for suspension stuff and was surprised about the amount of misinformation and confusion out there across forums and videos. Here ya'll go, hope this helps some of you DIYers. I recently got my truck running but the ignition switch doesn't work anymore, and theres some messed up wiring for oil pressure, turn signals and I'm assuming other stuff. Somehow it's isolated to the gauges and ignition system, fan and other lights work as normal.
Because when I got my system installed I brought the wires needed and told them. But when I got my car back the wires were still in my seat. And the guy on the phone before hand asked me what a big 3 upgrade was and I had to tell him🤦 Update as of September 04 2020. SOLVED! After digging around the wiring system looking for issues I finally found it... there is a ground on the spare tire bracket under the bed. This ground has a ground wire from the trailer accessories harness and the ground for the rear tail light harnesss. So a total of two ground wires attached. The trailer harness was grounded well but the tail light ground wire was corroded internally. It looked ok but after checking for continuity it read “open”. I repl...
Comments
Post a Comment